1624 Color Spectrum Instructions for Use
Scan the QR code on the back of the spectrum to view detailed instructions
1. Wiring method (Note: Try to use the voice control function and connect it to USB power supply)
1. Connect the USB cable to the 5V power supply and use a mobile phone charger or USB power supply device to supply power. The power supply voltage is 5V and the current is greater than 1A.
6. The voice-controlled device will beat as long as there is sound. If you need to use audio cable control, plug the audio cable into the headphone jack and it will automatically switch to the wire-controlled mode.
3. When using sound control, try to get as close to the speaker as possible. The sound sensor is at the back of the spectrum. There should be no obstructions between the sensor and the speaker. 4. When using voice control, external noise or speech will be received by the spectrum and displayed.
6. When using wired controls, turn up the volume of the sound source or increase the sensitivity value. Do not connect the speaker cable directly to the headphone input port of Spectrum, otherwise the signal will be too strong and it will easily fill the screen or burn out.
2. Button description (short press and long press)
There are two buttons on the back of the product, as shown in the picture below, button 1 and button 2. There are two pressing operation methods, one is long pressing and the other is short pressing.
Long press: Press and hold the switch for about 1 second (you will hear a buzzing sound), and then the setting interface will pop up. Short press: Just press and release the switch quickly (you will also hear a buzzing sound), and then the setting interface will pop up. Exit settings: Press another button to exit the current settings, or it will exit automatically after 8 seconds. Settings will be automatically saved when exiting
Allow.
Button 1/Button 2
Short press button 1: Set the display effect, press it once to change it
Short press button 2: set the color, press it once to change it, OFF means turning off the spectrum function.
Long press button 1: Enter the function settings. The settings are relatively complicated. Please check the electronic manual for detailed settings. After setting the time, just press the default settings for other settings.
3. Time setting
Setting method (no key press within 8 seconds will automatically exit)
UI
Press and hold button 1 and release it when you hear a buzzing sound; the time setting interface is displayed and the time flashes.
Then press the button continuously to modify the hour value.
-244
Press and hold button 1 again, you will hear a sound from your mouth and release it, and 2418 will flash. Then press the button continuously to modify the 24-hour and 12-hour format.
Press and hold button 1 again, release it when you hear a sound from your mouth, and the setting interface will be displayed and the points will flash. Then press the button continuously to modify the minute value.
Sensitivity setting: 1-12: Detect the input signal strength. The larger the value, the higher the sensitivity. If the sensitivity is too high, a little interference signal or sound will cause beating.
Spirituality
IT
In this way, the setting is completed. Press another button (button 2) to exit, or automatically exit after 8 seconds. For other settings, just follow the default settings. Long press button 2 to restore factory settings.
| Brand | Diydeg |
|---|---|
| Manufacturer | Diydeg |
| Model | Diydegbgqgy486t2 |
| Part Number | Diydegbgqgy486t2 |
| Light Source Type | Light Emitting Diode |
| Special features | Colour Changing |
| Mounting Hardware | Power Cable |
| Wattage | 3 watts |
| Power source type | Corded Electric |
| Batteries included | No |
| Batteries Required | No |
| Connector Type | USB |
| Material Type | Acrylonitrile Butadiene Styrene |
| Mounting type | Tabletop mount |
| Manufacturer | Diydeg |
| Item model number | Diydegbgqgy486t2 |
| Parcel Dimensions | 26.9 x 11.2 x 5.7 cm; 300 g |
| ASIN | B0C2F7QJ3B |
