The Community is a hub for connecting with your peers and Cisco specialists to ask for help, share your expertise, build your network, and grow professionally. New Here? Click here to learn more and get started.
Cisco Community is an active and collaborative place to learn more about our products and ask questions of peers and Cisco experts! Check out some of the most popular conversations happening right now!
Hi All,We have Room Kit in our setup which is running on ce-9.5.1-be5deaf82e6-2018-10-19, I have tried to upgrade the same to ce10_19_5_6. The package is about 1.5 GB so I couldn't do the local upgrade through web page.So I tried over CUCM, Installed...
Good afternoon, I had been using my DX80 as a 2nd monitor with my machine without issue, however I don't currently have the ability to connect my DX80 to a network. I can't figure out how to use the DX80 as a 2nd monitor without having network conne...
I am trying to develop a role that will turn off the 2.4 and 5 ghz radios and set the desired country codes then turn them back on.role logic:- name: Turn off 2.4 and 5 Ghz radios cisco.ios.ios_config: lines: - "ap dot11 24ghz shutdown" ...
Hi, hoping to get some feedback around best practice on certificate validity periods for EAP-TLS certficates for 802.1x clients.Thoughts around setting expiry for over 2 years etc.
I'm looking for the firmware that has OpenFlow support for the Cisco C3850-24T-E switch, but the Cisco website tells me that it is no longer found. Do you know where I can get it?They are the following:1. Firmware: cat3k_caa-universalk9.SPA.03.07.03....
hello show license statusI would like to disable smart license enable inI looked it up and it seems to be enabled by default. Is there anything in Cisco's official documentation?
We have an occurring issue across the board with our N9k's. Each site has a pair of N9k's connected redundantly to many catalyst switches, and all traffic going out to these switches only use one link, and the N9k's do not load balance the traffic g...
Hi, I have some APs which are not connecting to 9800 controllers. Reason for last AP connection failure is showing as "DTLS close alert from peer" or "DTLS handshake expired." Can anybody please explain how to resolve this issue?Thanks in advance.
I need a solution or plugin where receiver needs to decrypt the email received over Outlook. In current scenario both sender and receiver organizations use Outlook and there is an inbuilt feature within outlook for encryption which decrypts encrypted...
Hi Team,I have gone through roles Rest API https://developer.webex.com/docs/api/v1/rolesThis doesn't list down all roles belonging to site, it just list down roles only roles relevant to an admin.I want a API which will fetch all roles of the site/we...
Hi All, I have one cisco 3845 router and fan-3 went faulty, can you please suggest this this fan hot swappable. AUX(-48V) PS1 is absent.AUX(-48V) PS2 is absent.Fan 1 NormalFan 2 NormalFan 3 FailedFan Speed is NormalAlert settings:Intake temperature w...
2 cisco rourters, directly connected and assigned /30 ip addresses on each interfaces.I can see /30 as Connected and /32 as Local on show ip route on both routers.I enabled BGP and redistribute connected. No filter, no static and no other protocols ...
Bonjour!J'ai le CBS350, j'ai configuré 3 VLANs, ainsi que les IPV4 de ces VLANs, activé le IPv4 Routing, et activé également le DHCP sur chaque VLANs, jusque là tout fonctionne bien, j'arrive à ping d'un vlan à l'autre et tout se configure tout seul,...
Hello Team, We are going to migrate cisco old ACI to New ACI Fabric l2 migration. 1) Can we perform migration like l2 or how? 2) Anyone have done this type of migration please share steps. Thanks Suraj Sutar